NTC Thermistor

- the NTC thermistor is the more widely used of the two forms of thermistor - the abbreviation NTC standing for negative temperature coefficient.

The NTC thermistor is widely used in many applications for a variety of purposes.

The NTC thermistor, as the name indicates has a negative temperature coefficient, having a decreasing resistance for an increasing temperature.

NTC thermistor basics

A negative temperature coefficient or NTC thermistor is version of the basic thermistor that exhibits a large, predictable change in resistance corresponding to changes in absolute body temperature.

For a negative temperature coefficient, NTC thermistor there is a reduction in resistance for an increase in body temperature.

The change in body temperature of the NTC thermistor can be brought about in two main ways:

  • Raising external temperature:   raising the temperature of the external fluid, possibly air in which the NTC thermistor is placed will cause the body of the device to change its temperature and hence its resistance will change.
  • Passage of current through the device:   Passing current through the NTC thermistor will cause heat to be dissipated (Watts = Volts x Amps). This will cause the temperature to rise.

Typically NTC thermistors exhibit a change in resistance of between about -3%/°C to -6%°C at 25°C. The actual relationship follows a curve that is approximately exponential, with much higher changes in resistance at lower temperatures, and lowering considerably at higher temperatures.

The curve showing temperature and resistance for an NTC thermistor.
The Resistance vs. Temperature graph for an NTC Thermistor

The type of material used will govern many of the properties, but at temperatures around -40°C, the resistance change can be up to -8%/°C but at in the flatter part of the NTC thermistor curve it can be as low as -1%/°C at temperatures above 200°C or so.

NTC thermistor structure & materials

Thermistors can physically take a number of forms. NTC thermistors can be manufactured in the form of pressed discs, rods, plates, beads or even a semiconductor chip for example using a sintered metal oxide.

Often metallic oxide NTC thermistors are made from fine powers that are compressed and sintered at high temperature. Materials used include Mn2O3, NiO, Co2O3, Cu2O, Fe2O3, TiO2 and the like. They may also be manufactured from silicon or germanium crystals that are doped to provide the required level of conduction.

NTC thermistors operate because a rise in temperature results in the number of active charge carriers increasing as they are freed from the crystal lattice.

The method of conduction varies according to the type of material. In the case of ferric oxide, Fe2O3 doped with titanium gives an N-type semiconductor and in this case the majority charge carriers are electrons. In other materials like nickel oxide, NiO doped with lithium, Li form a p-type semiconductor where the majority charge carriers are holes. Either way, the same basic characteristics of an NTC thermistor are exhibited.

the choice of material for the NTC thermistor depends on many factors, although one of the major ones is the temperature range required.

Germanium NTC thermistors are generally used for temperatures in the range 1 - 100°K (i.e. absolute). Silicon ones for temperatures up to 250°K - they cannot be used above this because a positive temperature coefficient takes over above this temperature. Metallic-oxide NTC thermistors are used for the range 200 - 700°K. For higher temperatures still, very stable compounds are required and NTC thermistors for these temperatures may be made from materials including: Al2O3, BeO, MgO, ZrO2, Y2O3 and Dy2O3.

By Ian Poole

<< Previous   |   Next >>

Share this page

Want more like this? Register for our newsletter

Tick-Tock: What Your Engineers Could be Spending Time Doing if They Weren’t Stuck Designing a Display? Markku Riihonen | 4D Systems
Tick-Tock: What Your Engineers Could be Spending Time Doing if They Weren’t Stuck Designing a Display?
As soon as any design project is embarked upon, the clock starts ticking. The length of time needed to develop a system can impinge heavily on its commercial success. Windows of opportunity could be missed if it takes too long to complete, with products from rival companies gaining greater market share.

Radio-Electronics.com is operated and owned by Adrio Communications Ltd and edited by Ian Poole. All information is © Adrio Communications Ltd and may not be copied except for individual personal use. This includes copying material in whatever form into website pages. While every effort is made to ensure the accuracy of the information on Radio-Electronics.com, no liability is accepted for any consequences of using it. This site uses cookies. By using this site, these terms including the use of cookies are accepted. More explanation can be found in our Privacy Policy