22 Jun 2018

Doherty Amplifiers for UHF

Walter Sneijers, RF Application Engineer, Ampleon looks Doherty amplifiers for use at UHF and how to obtain the highest efficiency levels.

The triple demands of high efficiency, small size and low cost placed by cellular telephony on UHF transmitters led to the early introduction of Doherty amplifiers in mobile handsets. Since this introduction Doherty architectures have been further enhanced, leading to a gradual uptake of this technology in broadcasting, to the point where Doherty amplifiers are found in almost all of today’s new UHF transmitters.

This article looks at a selection of Doherty architectures and shows how the Ampleon BLF8xx transistor family may be used in UHF amplifier solutions based on Doherty architectures.

Doherty Architectures

In the following sections two common Doherty architectures are reviewed, the classical 2-way and the ultra wide-band, (UWB) architectures.

Classical 2-Way Doherty Architecture

Fig 1a shows a classical Doherty power amplifier architecture which actually consists of two amplifiers: one operating as a main, or “carrier”, amplifier biased as Class AB, the other as a “peaking” amplifier biased for Class C operation to provide a high-efficiency power boost when needed for higher-power input excursions. The input signal is evenly split using a 3-dB quadrature coupler. The two outputs from the coupler are 90⁰ out of phase and are brought back into phase and reactively combined using the quarter-wave transmission line of the peaking amplifier. The two signals in parallel create an impedance of Z0/2 Ω which is stepped up to Z0 Ω by the quarter-wave transformer.

Classical symmetric two way Doherty amplifier

An amplifier based on the classic Doherty architecture only operates over a 50 MHz bandwidth range and has somewhat limited power levels, but it does provide high efficiency for signals with high peak/average ratios.

An example of the implementation of a classical 2-way Doherty amplifier can be achieved using Ampleon’s BLF888A/B transistors, giving an amplifier with a 220 W average power level and 45% efficiency. In this configuration, the high-ruggedness BLF888A should be used in the peak amplifier and the high efficiency BLF888B in the main.

The a-symmetric Doherty architecture, shown in fig 1b, gives a 2 – 3 % increase in average efficiency compared to the above classic 2-way design and this architecture also offers increased power levels.

Hybrid variant of Doherty amplifier

This design uses the same main amplifier but with a higher power peak amplifier and can be implemented, for example, using Ampleon’s BLF888B, (Main) and BLF898, (Peak). In this case the BLF898 peak amplifier, with around 900 W, has around 1.5 times the power of the BLF888B main amplifier, with 650 W, giving an α = 0.4, (where α is the ratio of the main amplifier power over the sum of the main and peak amplifier powers). Figures 2a and 2b show how higher amplifier efficiencies can be obtained by varying the power of the peak amplifier.

Note however that this design is more complex than the classic 2-way and the relatively small increase in power and efficiency may or may not justify this extra complexity.

Instantaneous efficiency of Doherty amplifier

Doherty amplifier efficiency as a function of PAR

Ultra Wideband 2-Way Doherty Architecture

The Ultra Wideband Doherty (UWD) architecture was developed to overcome some of the bandwidth limitations of the classical design. The additional bandwidth is achieved by making changes to the output circuitry of the architecture, as shown in figure 4. The relative positions of the power combiner and impedance matching circuits are swapped and capacitance is added to the outputs of the amplifiers.

A theoretical UWD design enables coverage of the full UHF spectrum, albeit at a reduced efficiency level, as shown in figure 3a. However practical considerations such as parasitics in the output stages and 2nd order harmonics limit the achievable bandwidth.

Doherty amplifier bandwidth

An implementation of this design is possible using the Ampleon BLF888D transistor which enables full coverage of the UHF band at 40% efficiency with an output power of 115 W avg. However the efficiency of this implementation is limited by the nature of the output circuitry and also 2nd order harmonics introduced by channel filters. These and other factors are difficult to mitigate and can significantly lower efficiency, by as much as 5%.

Given these limitations it is important to be able to combine UWB Doherty amplifiers in order to achieve full UHF bandwidth coverage at acceptable efficiency levels and this is discussed in more detail below.

As with the classic Doherty architecture, an asymmetric approach can also be used in UWB Doherty amplifiers in order to improve power and efficiency. Figure 3b shows how, with an α of 0.4, efficiency is improved and the efficiency response is also flatter than for the symmetric UWB design. The theoretical bandwidth available from this approach is however around 50% of that obtained from the symmetric design, meaning that, realistically, the full UHF spectrum cannot be acceptably covered using UWB Doherty techniques.

If however the UHF spectrum is split into three sub-bands, e.g. 470-600 MHz, 600-700 MHz and 700-800 MHz then higher efficiency levels are achievable since Doherty designs are less susceptible to 2nd order harmonics and output matching can be improved when the covered spectrum is lower. As an example of what can be achieved by this approach, Ampleon have produced a development board, based on the BLF888D transistor, which enables 45% efficiency at an average power of 130 Watts over the 470-600 MHz sub-band.

Doherty amplifier bandwidth

The above discussion has illustrated the trade-off between efficiency and bandwidth when using current UWD technologies. This choice will be influenced in different regions by factors such as transmitter requirements, (size, cost and power consumption) and end-user requirements – again predominantly cost and size. The evolving regulatory landscape may also influence design changes as regional authorities review future use of UHF spectrum.

Doherty amplifier bandwidth

Combining of UWD Amplifiers

Where power and efficiency requirements dictate that the UHF spectrum must be split into sub-bands then amplifier outputs must be combined. Three main combining techniques are commonly used in UHF solutions – Wilkinson Combiners, Baluns and 90° couplers, each with their respective pros and cons.

In this section we focus on the 90° coupler and the Balun and examine their performance when isolating 2nd order harmonics – a key characteristic of any coupling device.

Doherty amplifier combination with a balun


An ideal balun provides:

• Balanced to unbalanced conversion or vice versa • Impedance transformation at fundamental frequencies (optional) • Cancellation of even harmonic signals towards the load (prevent even harmonic reflections from the channel filter) • An “open” for even harmonic signals seen at the balun input

Whilst the balun is the most commonly used combiner in UHF broadband amplifiers it has significant limitations when used with UWB Doherty amplifiers due to 2nd order harmonic resonances which can cause in-band interference, resulting in significant power and efficiency losses in some channels.

Although this precludes the use of baluns from any Doherty designs covering the full UHF band, they can be used in solutions where the UHF band is divided into sub-bands, as shown in figure 5c - below, where 120 MHz bandwidth is achievable.

90° Coupler:

Nowadays, in most cases the combiner used with UWD amplifiers is a 90° coupler, a four-port device used either to equally split an input signal with a resultant 90° phase shift between output ports or to combine two signals while maintaining high isolation between the ports.

Doherty amplifier 90 degree coupler and second harmonic reflection

This configuration ensures a high degree of isolation between the two output ports and the two input ports without unwanted interaction between them. The characteristics of the coupler are such that the direct, or 0 path isolates 2nd harmonic reflections and the 90° path passes on 2nd harmonic reflections.

Doherty amplifier 90 degree coupler

This means that only one amplifier will see a harmonic reflection – see fig 6a. When more 90° couplers are used (see Fig. 6b: three couplers used) only one transistor out of four will see a full reflection.

Page 1 of 1

About the author

Walter Sneijers is Principal Application Engineer with Ampleon and has over 20 years experience in the design of LDMOS wide-band UHF power amplifiers used for broadcast applications. Prior joining Ampleon in 2015, Walter worked for NXP Semiconductors and HTS Netherlands. He has co-authored many papers that have been published by the IEEE and RF/microwave industry trade publications.

Created in 2015, Ampleon is shaped by 50 years of RF power leadership. Recently being spun-off from NXP Semiconductors, the company is set-out to exploit the full potential of data and energy transfer in RF. Ampleon has more than 1,250 employees worldwide, dedicated to creating optimal value for customers. Its innovative, yet consistent portfolio offers products and solutions for a wide range of applications, such as cellular base stations, radio/TV/broadcasting, radar, air traffic control, cooking, lighting, industrial lasers and medical.

Most popular articles in RF topics

  • Integrated PLLs and VCOs for Wireless Applications
  • Demystifying PIM – Passive Intermodulation Products
  • Software defined power amplifiers using envelope tracking
  • Measuring Noise Figure on RF systems
  • Locating Passive Intermodulation, PIM Faults
  • Share this page

    Want more like this? Register for our newsletter

    2019 Electronic Component Market Supply Forecast  Ian Poole | Electronics Notes
    2019 Electronic Component Market Supply Forecast
    Electronic supply has a major impact on manufacturers and as a result it is an aspect of the industry that many are keen to forecast and prepare for and changes in the industry.

    Radio-Electronics.com is operated and owned by Adrio Communications Ltd and edited by Ian Poole. All information is © Adrio Communications Ltd and may not be copied except for individual personal use. This includes copying material in whatever form into website pages. While every effort is made to ensure the accuracy of the information on Radio-Electronics.com, no liability is accepted for any consequences of using it. This site uses cookies. By using this site, these terms including the use of cookies are accepted. More explanation can be found in our Privacy Policy