PCB Inspection Techniques & Technologies

- notes and details on maximising manufacturing yields through using electronics inspection technologies including AOI, AXI, etc.

PCB inspection is an essential element in any electronics manufacturing process.

The PCB inspection enables faults to be detected as soon after the manufacture process as possible.

As such the PCB inspection process is an essential element of any PCB manufacturing process.

Whether for large scale / high volume or low volume manufacturing, the PCB inspection process is essential, especially with the high level of complexity or many of today's boards.


PCB inspection basics

In the early days of PCB manufacture, or the manufacture of any electronics equipment, all inspection was undertaken manually. This was the best option, but was recognised as having only limited value. The repetitive nature of the process meant that many faults were not spotted and passed on into the next stage of production undetected.

There are various methods by which PCB inspection can be achieved:

  • Manual PCB inspection :   As the name implies, manual inspection involves individual inspectors looking at boards or other assemblies to inspect them for problems. This approach has been proved to be costly, and yielding poor results. Before automation, it was the only way that inspection could be performed.
  • AOI PCB inspection:   Automatic or automated optical inspection is the preferred method of PCB inspection. It utilises an optical system that takes an image of a good assembly and compares the two images to detect any faults or other issues.

    This form of PCB inspection is widely used and has been perfected so that it operates very reliably.
  • AXI PCB inspection:   With density on PCBs increasing and new IC mounting technologies being used, not all solder joints may be visible. Particularly when new boards are being manufactured and new set-ups being used, it is very important to check that solder joints on packages such as BGAs (Ball Grid Arrays) are being correctly soldered. Optical inspection cannot achieve this because the solder joints are not visible. The only option is to use an X-Ray system - Automated X-Ray Inspection, AXI, that is able to look under the chips to view the solder joints. Although expensive and only used for a small proportion of the solder joints, etc, they are necessary in many instances.

For high volume production these days most manufacturers use AOI systems for their PCB inspection functions. With the increase in the number of BGAs and BGA associated packages being used, AXI is also being increasingly used.


PCB inspection in a manufacturing process

There are two main uses for a PCB inspection system:

  • High light manufacturing defects:   The obvious function of a PCB inspection system is to highlight any defects so that they can be corrected before they are passed on to the next stage in the production process. Finding faults as early as possible in the production process is essential because fault finding and fixing costs rise by approximately a factor of ten as each stage in the production process is passed.
  • Provide process feedback:   An equally important function of a PCB inspection system is to provide feedback into the manufacturing process. Using a PCB inspection system on the output of the soldering process can enable any pattern faults to be seen and the process corrected almost immediately to reduce or eliminate the occurrence of a given problem.

Production Process Flow Diagram
Manufactured PCB production process flow diagram

It can be seen from the diagram, that the PCB inspection process allows boards with failures to be detected as well as feedback to assist the production process to be gained.

Some production processes may also place a PCB inspection stage after the pick and place operation - indeed, some pick and place machines include an optical PCB inspection system. This allows PCBs to be corrected before being soldered.

By Ian Poole


. . . .   |   Next >


Share this page


Want more like this? Register for our newsletter








bluetooth 5 - why it is the key to the IoT Mats Andersson | u-blox
Bluetooth 5: Why it’s key to the IoT
Bluetooth 5 is the latest flavour of the popular wireless standard. It is anticipated that it will become even more widespread with is applicability to so many applications.
Whitepapers
Low Loss Dynamic Compression of CPRI Baseband Data
Read this paper from Altera that describes a method of using Mu-Law compression for Gaussian-like waveforms providing an efficient methodology.

More whitepapers










Radio-Electronics.com is operated and owned by Adrio Communications Ltd and edited by Ian Poole. All information is © Adrio Communications Ltd and may not be copied except for individual personal use. This includes copying material in whatever form into website pages. While every effort is made to ensure the accuracy of the information on Radio-Electronics.com, no liability is accepted for any consequences of using it. This site uses cookies. By using this site, these terms including the use of cookies are accepted. More explanation can be found in our Privacy Policy