Software Defined Radio SDR Hardware

- overview / essentials about the key areas of importance for the software defined radio, SDR, hardware, and the SDR hardware architecture used.

The hardware for a software defined radio is a particularly important element of the overall design. While the whole idea of the radio is that it is fundamentally driven by software, it still needs the basic hardware to enable the software to run.

the software defined radio hardware presents some interesting challenges to the hardware development engineer. The performance of the hardware will define exactly how much can be done within the software.

With the interface between software and hardware controlled functions needing to be as close to the antenna as possible to provide greater levels of software control and hence reconfigurability, this provides greater challenges in terms of design, performance and cost. As a result, decisions need to be made at the earliest stages of any design to determine where the boundary will be, based on functionality required, performance and cost.


SDR hardware architecture

Although there are many different levels of SDR and many ways in which a software defined radio may be designed, it possible to give some generalised comments about the basic structures that are used.

Block diagram of an ideal Software Defined Radio

Block diagram of an 'Ideal' Software Defined Radio
No frequency conversion is used in this configuration as the A2D and D2A conversion takes place at the frequency of operation

Apart from the control and management software and its associated hardware, a software defined radio (SDR) can be considered to contain a number of basic functional blocks as detailed below:

  • RF Amplification:   These elements are the RF amplification of the signals travelling to and from the antenna. On the transmit side the amplifier is used to increase the level of the RF signal to the required power to be transmitted. It is unlikely that direct conversion by the DAC will give the required output level. On the receive side signals from the antenna need to be amplified before passing further into the receiver. If antenna signals are directly converted into digital signals, quantisation noise becomes an issue even f the frequency limits are not exceeded.
  • Frequency conversion:   In many designs, some analogue processing may be required. Typically this may involve converting the signal to and from the final radio frequency. In some designs this analogue section may not be present and the signal will be converted directly to and from the final frequency from and to the digital format. Some intermediate frequency processing may also be present.
  • Digital conversion:   It is at this stage that the signal is converted between the digital and analogue formats. This conversion is in many ways at the heart of the equipment.

    When undertaking these conversions there are issues that need to be considered. On the receive side, the maximum frequency and number of bits to give the required quantisation noise are of great importance. On the transmit side, the maximum frequency and the required power level are some of the major issues.
  • Baseband processor:   The baseband processor is at the very centre of the software defined radio. It performs many functions from digitally converting the incoming or outgoing signal in frequency. These elements are known as the Digital Up Converter (DUC) for converting the outgoing signal from the base frequency up to the required output frequency for conversion from digital to analogue. On the receive side a Digital Down Converter (DDC) is used to bring the signal down in frequency. The signal also needs to be filtered, demodulated and the required data extracted for further processing.

    One of the key issues of the baseband processor is the amount of processing power required. The greater the level of processing, the higher the current consumption and in turn this required additional cooling, etc. This may have an impact on what can be achieved if power consumption and size are limitations. Also the format of any processing needs to be considered - general processors, DSPs, ASICs and in particular FPGAs may be used. FPGAs are of particular interest because they may be reconfigured to change the definition of the radio.

By Ian Poole


<< Previous   |   Next >>



Read more radio receiver tutorials . . . . .

Superhet radio Sensitivity Software radio Cognitive radio
FM demod AM demod DSP tutorial Selectivity & filters
Want more like this? Register for our newsletter









Whitepapers
Redefining LTE for IoT
Find out how LTE with its high data rates, complexity and capacity can be used to provide effective communications for IoT with its lower complexity and data rate requirements.

More whitepapers

Radio Receiver Technology: Principles, Architectures and Applications
Radio Receiver Technology: Principles, Architectures and Applications

Ralf Rudersdorfer
As the name implies, this book provides a complete description of current radio...
Read more . .

USA bookstore UK bookstore









Radio-Electronics.com is operated and owned by Adrio Communications Ltd and edited by Ian Poole. All information is © Adrio Communications Ltd and may not be copied except for individual personal use. This includes copying material in whatever form into website pages. While every effort is made to ensure the accuracy of the information on Radio-Electronics.com, no liability is accepted for any consequences of using it. This site uses cookies. By using this site, these terms including the use of cookies are accepted. More explanation can be found in our Privacy Policy