UMTS TDD / TD WCDMA

- a summary or tutorial about the basics of UMTS TDD, the time division duplex cellular technology sometimes called TD WCDMA, part of the UMTS 3G system.

UMTS TDD (Universal mobile telecommunications system - time division duplex) is a growing cellular technology. Although UMTS TDD or TD WCDMA is not as widely deployed as the more popular UMTS FDD which is being deployed for the 3G mobile phone systems, UMTS TDD is nevertheless being widely used and providing a viable service for many applications. In particular it is being used to provide mobile broadband data services, and other applications may include its use in providing mobile TV applications. In this way, UMTS is a growing cellular technology which will be far more widely used in the years to come


TDD - time division duplex

A communications system requires that communication is possible in both directions: to and from the base station to the remote station. There are a number of ways in which this can be achieved. The most obvious is to transmit on one frequency and receive on another. The frequency difference between the two transmissions being such that the two signals do not interfere. This is known as frequency division duplex (FDD) and it is one of the most commonly used schemes, and it is used by most cellular schemes.

It is also possible to use a single frequency and rather than using different frequency allocations, use different time allocations. If the transmission times are split into slots, then transmissions in one direction take place in one time slot, and those in the other direction take place in another. It is this scheme that is known as time division duplex, TDD, and it is used for UMTS-TDD.


Note on TDD and FDD duplex schemes:

In order for radio communications systems to be able to communicate in both directions it is necessary to have what is termed a duplex scheme. A duplex scheme provides a way of organizing the transmitter and receiver so that they can transmit and receive. There are several methods that can be adopted. For applications including wireless and cellular telecommunications, where it is required that the transmitter and receiver are able to operate simultaneously, two schemes are in use. One known as FDD or frequency division duplex uses two channels, one for transmit and the other for receiver. Another scheme known as TDD, time division duplex uses one frequency, but allocates different time slots for transmission and reception.

Click on the link for more information on TDD FDD duplex schemes


When using a TDD system, there are a number of characteristics that are pertinent for TDD systems. These characteristics need to be accommodated when developing or using TDD systems.

  • Utilisation of unpaired bands:   Typically there is more traffic in the downlink (network to the mobile) than in the uplink (mobile to network). Accordingly the operator is able to allocate more time to the downlink transmission than the uplink. This is not possible with the paired spectrum required for FDD systems where it is not possible to re-allocate the use of the different bands. As a result of this, it is possible to make very efficient use of the available spectrum.
  • Discontinuous transmission:   In any TDD system it is necessary to switch between transit and receive. This takes a certain amount of time. Not only does it take time for the mobile and the base station to change between transmit and receive in terms of ramping up or down the power, along with the settling of any transients. In addition to this the time is required between transmit and receive to accommodate the transmission time between the mobile and the base station. As a result a guard band is required.
  • Uplink / downlink interference:   As both uplink and downlink share the same channel there can be interference between the two transmission directions. To overcome this, base stations are synchronised to ensure that they do not transmit when an adjacent base station is receiving, otherwise the better siting and possible higher power level will cause interference.
  • Equivalent conditions for uplink and downlink:   As both uplink and downlink use the same channel, they are subject to the same propagation conditions. With FDD systems using different frequencies for the uplink and downlink there are significant differences. By using the same frequency fading conditions can be counteracted more effectively.

UMTS TDD / FDD comparison

While UMTS TDD and UMTS FDD are both specified in the same standard and share very many properties, there are naturally some differences.


Parameter UMTS TDD UMTS FDD
Multiple access method TDMA, CDMA CDMA
Duplex method TDD FDD
Channel spacing 5 MHz[1] 5 MHz
Carrier chip rate 3.84 Mcps 3.84 Mcps
Time slot structure 15 / 14 slots / frame 15 slots / frame
Frame length (ms) 10 10
Multirate concept Multicode, multislot and OVSF[2] Multicode, and OVSF[2]
Burst types (1) traffic bursts
(2) random access burst
(3) synchronisation burst
N/A
Detection Coherent based on midamble Coherent based on pilot symbols
Dedicated channel power control Uplink: open loop 100 Hz or 200 Hz rate
Downlink: closed loop max 800 Hz rate
Fast closed loop 1500 Hz rate
Spreading factors 1 .. 16 4 .. 512

Notes
[1] for TD-SCDMA the channel spacing is 1.6 MHz
[2] OVSF = Orthogonal variable Spreading Factor


UMTS TDD within 3GPP

All the standards for UMTS 3G systems have been defined under the auspices of 3GPP - the third generation partnership project. The standards not only define the FDD systems, but also the TDD system.

In these specifications, it was the original intent of UMTS that the TDD spectrum would be used to provide high data rates in selected areas forming what could be termed 3G hot zones.


UMTS TDD details

UMTS TDD uses many of the same basic parameters as UMTS FDD. The same 5 MHz channel bandwidths are used. UMTS TDD also uses direct sequence spread spectrum and different users and what can be termed "logical channels" are separated using different spreading codes. Only when the receiver uses the same code in the correlation process, is the data recovered. In W-CDMA all other logical channels using different spreading codes appear as noise on the channel and ultimately limit the capacity of the system. In UMTS TDD, a scheme known as multi user detection (MUD) is employed in the receiver and improves the removal of the interfering codes, allowing higher data rates and capacity.

In addition to the separation of users by using different logical channels as a result of the different spreading codes, further separation between users may be provided by allocating different time slots. There are 15 time slots in UMTS TDD. Of these, three are used for overhead such as signalling, etc and this leaves twelve time slots for user traffic. In each timeslot there can be 16 codes. Capacity is allocated to users on demand, using a two dimensional matrix of timeslots and codes.

In order for UMTS TDD to achieve the best overall performance, the transport format, i.e. the modulation and forward error correction can be altered for each user. The schemes are chosen by the network, and will depend on the signal characteristics in both directions. Higher order forms of modulation enable higher data speeds to be accommodated, but they are less resilient to noise and interference, and this means that the higher data rate modulation schemes are only used when signal strengths are high. Additionally the levels of forward error correction can be changed. When errors are likely, i.e. when signal strengths are low or interference levels are high, Similarly higher levels of forward error correction are needed under low require additional data to be sent and this slows the payload transfer rate. Thus it is possible to achieve much higher data transfer rates when signals are strong and interference levels are low.


Spectrum allocations for UMTS TDD

Standard allocations of radio spectrum have been made for 3G telecommunications systems in most countries around the globe. In Europe and many other areas spectrum has been allocated for UMTS FDD between 1920MHz to 1980MHz and 2110MHz to 2170MHz. For UMTS TDD spectrum is primarily located between 1900MHz and 1920MHz and between 2010MHz and 2025MHz. In addition to this there are some other allocations around 3 GHz.


UMTS TDD performance

UMTS TDD is able to support high peak data rates. Release 5 of the UMTS standard provides HSDPA (high-speed downlink packet access). The scheme allows the use of a higher order modulation scheme called 16-QAM (16 point quadrature amplitude modulation), which enables peak rates of 10 Mbps per sector in commercial deployments. The next release increases the modulation to 64-QAM, and introduces intercell interference cancellation (called Generalized MUD) and MIMO (multiple in, multiple out). In combination, these increase the peak rate to 31 Mbps per sector.

By Ian Poole


<< Previous   |   Next >>


Share this page


Want more like this? Register for our newsletter






Refining IoT Technology to Address Demands of the Healthcare Market Mark Patrick | Mouser Electronics
Refining IoT Technology to Address Demands of the Healthcare Market
The Internet of Things, IoT is destined to affect many areas of everyday life - we expect it will include many areas like smart meters, remote control of lighting, but what about the healthcare market . . .
Whitepapers
LTE for Automotive Applications
Read the insight in this white paper from u-Blox about LTE for automotive applications. Discover all you need to know.

More whitepapers










Radio-Electronics.com is operated and owned by Adrio Communications Ltd and edited by Ian Poole. All information is © Adrio Communications Ltd and may not be copied except for individual personal use. This includes copying material in whatever form into website pages. While every effort is made to ensure the accuracy of the information on Radio-Electronics.com, no liability is accepted for any consequences of using it. This site uses cookies. By using this site, these terms including the use of cookies are accepted. More explanation can be found in our Privacy Policy