Quarter wave vertical antenna

- overview or summary about the basics of the quarter wave vertical and ground plane antennas that ares widely used for medium wave broadcasting, mobile radio communications applications and many more.

Vertical antennas are widely used at all frequencies from MF up to VHF and beyond. They exist in a variety of forms including the quarter wave vertical and ground plane antennas. They possess many advantages and are widely used for medium wave broadcasting as well as for mobile applications in areas including private mobile radio.

The reason for this widespread use is the omni-directional radiation pattern that they give in the horizontal plane. This means that the antennas do not have to be re-orientated to keep the signals constant as the car moves it position.

Single element vertical antennas posses an omni-directional radiation pattern (in the horizontal plane). This means that the antennas do not have to be re-orientated when used in mobile applications as the vehicle moves. This is obviously an essential requirement.

A further advantage is that much of the radiation is at right angles to the antenna element, and as a result it travels close to the earth's surface where the receiving stations are located. Radiation directed upwards is wasted in many instances as VHF transmissions are normally not reflected by the ionosphere.,/p>

For medium wave broadcast stations a particular advantage is that the radiation is vertically polarised. It is found that the vertically polarised transmissions propagate further via the ground wave that these transmissions use.


Basic element

Like the name suggests the antenna consists of a quarter wavelength vertical element. The antenna is what is termed "un-balanced" having one connection to the vertical element and using an earth connection or simulated earth connection to provide an image for the other connection.

The voltage and current waveforms show that at the end the voltage rises to a maximum whereas the current falls to a minimum. Then at the base of the antenna at the feed point, the voltage is at a minimum and the current is at its maximum. This gives the antenna a low feed impedance. Typically this is around 20 ohms.

A quarter wave vertical RF antenna design

A quarter wave vertical RF antenna design

The ground is obviously an important part of the RF antenna. Many MF and HF installations use a ground connection for this. These ground systems need to be very effective fort he antenna to perform satisfactorily. They must obviously have a very low resistance, and often utilise large "mats" of radials extending out from the base of the antenna to ensure excellent RF performance.

For VHF and UHF installations, height is obviously important and antennas need to be raised to ensure they are above the nearby obstructions. Also for mobile installations it is clearly not possible to use a true earth connection. In these cases a simulated earth is used. For mobile applications this consists of the body of the vehicle. The antenna mounting will normally enable a suitable connection to be made to the vehicle body, sometimes using a capacitive connection. However it is necessary to ensure that the vehicle body is metal, and not plastic in the vicinity of the antenna mounting.

For fixed stations a set of radials simulating a ground plane is used. In theory the ground plane should extend out to infinity, but in practice a number of radials a quarter wavelength long is used. Typically for many VHF applications four radials is sufficient.

Radial system used with a quarter wave vertical RF antenna design

A radial system used with a quarter wave vertical

If the radials are bent downwards from the horizontal then the feed impedance will be raised. A 50 ohm match is achieved when the angle between the ground plane rods and the horizontal is 42 degrees. Another solution is to include an impedance matching element in the antenna. Normally this is in the form of a tapped coil that can be conveniently housed in the base of the antenna.


Folded element

In view of the low impedance presented to the feeder by the RF antenna, methods must be found of presenting a good match and some have already been outlined. Another is to use a folded element. In the same way that a folded dipole increases the feed impedance of the antenna, so a folded vertical element can be used. If the diameter of both sections is the same, then an increase by a ratio of 4:1 is achieved. This would bring the impedance to 80 ohms and will provide an acceptable match to 75 ohm feeder. By using a smaller diameter grounded element the feed impedance can be reduced so that a good match to 50 ohm coax can be achieved.


Summary

The quarter wave vertical antenna is widely used in view of its simplicity and convenience. To improve on its performance other types of vertical are available. It is also possilbe to use further verticals and feed them with different phases to provide gain to the overall antenna system.

By Ian Poole

Want more like this? Register for our newsletter









Whitepapers
R&S Higher Order MIMO Testing
Rohde & Schwarz presents this authoritative whitepaper on higher order MIMO testing.

More whitepapers

Training
Fundamentals of RF and Wireless Communications Engineering (RF1-1214)
Gain a thorough grounding in the fundamentals of modern RF and wireless communications engineering.

More training courses

The Art of Electronics
The Art of Electronics

Paul Horowitz & Winfield Hill
Now in Kindle, this is the classic electronics book. The Art of Electronics has...
Read more . .

USA bookstore UK bookstore









Radio-Electronics.com is operated and owned by Adrio Communications Ltd and edited by Ian Poole. All information is © Adrio Communications Ltd and may not be copied except for individual personal use. This includes copying material in whatever form into website pages. While every effort is made to ensure the accuracy of the information on Radio-Electronics.com, no liability is accepted for any consequences of using it. This site uses cookies. By using this site, these terms including the use of cookies are accepted. More explanation can be found in our Privacy Policy